Gumstix Pi HAT Sensor board


Gumstix Pi HAT Sensor Board is a Hardware Attached on Top (HAT) with a barometer, ambient temperature sensor, 9-axis motion detection, Pre-Go connectability, LEDs, and pushbuttons for Raspberry Pi.

Once you have tested the board and want to add more sensors, you may use Geppetto online to design and customize it for your own project.

Gumstix Pi HAT Sensor Board

The Pi HAT Sensor Board provides 9-axis motion detection, Pre-GO connectability, and ambient pressure and temperature sensors along with an LED array and pushbuttons. It also includes an RTC.

Customize Your Board

Customize the Gumstix Pi HAT Sensor Board to your project's specific needs in Geppetto D2O. Add functionality or remove unused components with the ease of a drag-and-drop interface.

Related Posts

Learn more about this product by checking out the following:

Articles from Gumstix Blog

Press Release

Included Components
Pi HAT Sensor Board Pi HAT Sensor Board

6-axis internal measurement unit (IMU)


Barometric pressure sensor


3-axis gyroscope

RTC Battery Holder

Holder for 6mm rechargeable coin cell RTC battery


Ambient temperature sensor

5-pin GPS Connector

UART connection for Gumstix Pre-GO modules

Key Components
Connector (Battery 6mm) Rechargeable coin battery holder
IC (RTC 1.8V) IC (RTC 1.8V)
Memory (256Kb I2C Serial Board EEPROM) CAT24C256 Series 256 kbit (32 K x 8) 1.8-5.5V I2C CMOS Serial EEPROM - TSSOP-8 Specs
MS5611 Barometric Sensor A high resolution altitude and digital atmospheric pressure sensor accurate to within 10 cm. Specs
IC DGTL TEMP SENSOR LP SOT-563 Temp Monitoring System (Sensor) Specs
LSM303D 6-Axis Accelerometer System-in-package featuring a 3D digital linear acceleration sensor and a 3D digital magnetic sensor. Specs
DF13 Top 5Pos 1.25mm CONN HEADER 5POS 1.25MM STR TIN
ST L3GD20H 3-Axis Gyroscope IC MEMS MOTION SENSOR 16LLGA. Updated version of ICL415 (L3G4200D) Specs
Mating Connectors

Please read the instructions in the README file carefully before starting. Instructions and functions are explained in the file.

Files that are needed (such as bootloader and operating system) to create a bootable disk image, are available below.

Our Support page links additional resources.

uEnv-geppetto.txt This is a simple uEnv.txt to select a GDT-generated device tree i.e. fdtfile=geppetto.dtb
2017-10-28/raspberrypi3/morty/gumstix-xfce-image-raspberrypi3.rpi-sdimg.xz gumstix-xfce-image-raspberrypi3.rpi-sdimg.xz ddable file generated by buildbot on 2017-10-28 for raspberrypi3 from morty
2017-10-28/raspberrypi3/morty/gumstix-console-image-raspberrypi3.rpi-sdimg.xz gumstix-console-image-raspberrypi3.rpi-sdimg.xz ddable file generated by buildbot on 2017-10-28 for raspberrypi3 from morty
2017-10-28/raspberrypi3/morty/gumstix-qt5-dev-image-raspberrypi3.rpi-sdimg.xz gumstix-qt5-dev-image-raspberrypi3.rpi-sdimg.xz ddable file generated by buildbot on 2017-10-28 for raspberrypi3 from morty
dt/nqFuZLWH.dtb Generated device tree for BRD900000000356