Autonomous Kit For Overo
The Autonomous Kit for Overo allows engineers and makers to build a complete, Overo-powered UAV with GPS and WiFi on a proven PX4-ready UAV controller board.
Autonomous Kit for Overo
The kit consists of the following components:
- AeroCore 2 for Overo
- Overo AirSTORM-Y COM
- Caspa VL (camera)
- USB Cable (micro-B to standard-A)
Powered by an AeroCore 2 for the Overo, which contains an ARM Cortex-M4 microprocessor, and an included Overo AirSTORM-Y, the Autonomous Kit For Overo offers all the tools you need for your unmanned aerial vehicle.
With NutX RTOS for real-time servo control and onboard WiFi 802.11b/g/n and Bluetooth 4.1 communications, the Autonomous Kit for Overo will have you flying in no time at all.
The brain of the kit is the AeroCore 2 MAV control board which runs NuttX RTOS for real time servo control and sensor measurements. The Overo COM provides access to onboard wifi and Bluetooth 3.0 and/or 802.11b/g/n wireless communications transmitted by the U.FL antenna. It is fully compatible with PX4 software, including MAVLink and QGroundControl and supports Mission Planner, ArduPilot and APM Planner.
|USB Cable (micro-B to standard-A)||USB Cable (micro-B to standard-A)|
|Caspa VL||**Caspa VL camera board** has a CMOS imager (Aptina MT9V032, 752 x 480, 60 FPS, color) making it ideal for robotics computer vision. Using an optical filter to cut out the IR range, the Caspa VL receives only visible spectrum light.|
|AeroCore for the Overo||AeroCore for the Overo|
|Overo AirSTORM-Y||Overo AirSTORM-Y|
|AeroCore 2 for the Overo (no GPS)||AeroCore 2 for the Overo (no GPS)|
3-Axis Accelerometer + 3-Axis Magnetometer
|Flash Memory (NAND)||
U-Blox NEO-7M GPS Receiver
OpenGL POWER SGX Graphics Accelerator
|Digital Signal Processor||
C64x Fixed Point DSP 660,800 Mhz (Max.)
3-Axis Angular Rate Sensor
3.3V-4.2V, provided by the attached Overo COM (not included)
Texas Instruments TPS65950
ARM Cortex-M4 Microcontroller
|Processor Base Clock||
Up to 1 GHz (recommended @ 800MHz)
Built with components rated -25C < T < 70C
USB Micro-AB Connector
|U.FL Antenna with Collar||U.FL antenna with collar for Bluetooth and/or 802.11b/g/n wireless communications.|
|microSD Card Slot||An onboard card-slot for system storage expansion using microSD cards.||Specs|
|Texas Instruments TPS65950 Power Management||The TPS65950 device is a highly integrated power-management integrated circuit (IC) that supports the power and peripheral requirements of the OMAP3-driven Overo series COMs.||Specs|
|W2CBW0015 Wifi+Bluetooth Module||This elegant combination from Wi2Wi enables both 802.11b/g/n and Bluetooth 3.0.||Specs|
|Micron 512MB DDR LPDRAM & 512MB NAND Flash Memory||Package-on-package (PoP) memory solution that minimizes power consumption, maximizes board space and increases speed.|
|Texas Instruments DM3730 Applications Processor||1GHz ARM Cortex-A8 DaVinci DM3730 high-performance microprocessor. Includes a 720p HD DSP imaging and video accelerator and PowerVR SGX graphics accelerator with Open GL ES 2.0 and OpenVG support. The DM3730 has been designed to provide best in class ARM and graphics performance while delivering low power consumption.||Specs|
|Aptina MT9V032C12STC Image Sensor||This ⅓” wide VGA CMOS digital image sensor provides exceptional image quality with superior color accuracy, low-light sensitivity, and low noise level.||Specs|
|Camera Flex Ribbon Cable (80mm, White)||This flex ribbon cable connects a Gumstix Caspa cameras to an Overo COM.|
|FTDI FT4232H Quad USB - Serial||Interface up to four devices over RS232 with an external USB connection with the FTDI FT4232 Quad USB - Serial converter.||Specs|
|Texas Instruments TPS62111 Step-Down Converter||A low-noise synchronous step-down DC-DC converter. **Component Max Vin:** 17V, 1.5A.||Specs|
|ST L3G4200D 3-Axis Gyroscope||Low-power three-axis angular rate sensor able to provide unprecedented stability of zero rate level and sensitivity over temperature and time.||Specs|
|Memory (SPI FRAM 1MB 1.8V)||Memory (SPI FRAM 1MB 1.8V)||Specs|
|MS5611 Barometric Sensor||A high resolution altitude and digital atmospheric pressure sensor accurate to within 10 cm.||Specs|
|LSM303D 6-Axis Accelerometer||System-in-package featuring a 3D digital linear acceleration sensor and a 3D digital magnetic sensor.|
|TI WiLink8 WL1831MOD||The certified WiLink 8 module from TI offers high throughput and extended range along with Wi-Fi and Bluetooth coexistence in a power-optimized design.||Specs|
|Texas Instruments AM3703 Applications Processor||1GHz ARM Cortex-A8 Sitara AM3703 high-performance microprocessor designed to provide best in class ARM and graphics performance while delivering low power consumption. According to Texas Instruments, AM3703 is fully backward compatible with previous OMAP™ processors.||Specs|
|Texas Instruments SN65HVD232 CAN Transceiver||Designed for use with Texas Instruments DSPs with CAN controllers and equivalent devices. Provides differential transmit and receive capability at speeds up to 1 Mbps.||Specs|
|FTDI FT232RQ USB UART Interface||Connect to an RS232 serial terminal over USB with the FTDI FT232RQ interface||Specs|
|U.FL Connector||Attach a U.FL Wi-Fi or Bluetooth antenna (not included) to a Gumstix system with this connector.|
|Hirose 27-Pin Camera Connector (Overo COMs)||Connect a Caspa camera to an Overo COM with this connector (Hirose FH26-27S-0.3SHW)||Specs|
|70-Pin AVX Connector (Male – Overo COMs)||Connect your Gumstix Overo COM to an expansion board with these 70-pin AVX connectors.||Specs|
|Molex Easy-On FPC Connector (Caspa Cameras)||A 27-pin FPC connector on Caspa cameras to connect to Overo COMs. (Molex 502250-2791)||Specs|
|70-Pin AVX Connectors (Female – Overo Expansion)||Connect an Overo COM to an expansion board with these 70-pin AVX connectors.||Specs|
Please read the instructions in the README file carefully before starting. Instructions and functions are explained in the file.
Files that are needed (such as bootloader and operating system) to create a bootable disk image, are available below.
Our Support page links additional resources.